超临界机组发生FAC的因素及相互关系分析

为了减轻因流动加速腐蚀(FAC)引起的锅炉结垢加速、汽水系统管道厚度减小甚至爆裂现象，对超临界机组发生流动加速腐蚀的机理及其主要影响因素进行了研究，并讨论了管壁内表面粗糙度、蒸汽含汽率、pH值、溶氧量对FAC的影响，以及温度与pH值、温度与流速、pH值与溶解氧量、溶解氧量与氢电导率等影响因素之间的相互作用关系，最后结合实际电厂的运行数据验证了分析结果。研究表明：减小工质流速、管壁粗糙度和氢电导率，增大给水的pH值和溶解氧含量可以使FAC的腐蚀速率减小，超临界加氧处理时pH值应在8.9～9.2之间，溶解氧量范围为45～100μg/L,氢电导率的期望值在0.1μS/cm以下。由于各影响因素之间的作用十分复杂，本文只给出了大致范围和趋势，并未给出准确数据。     

Co?N graphene encapsulated cobalt catalyst for H2O2 decomposition under acidic conditions

Hydrogen peroxide (H₂O₂) has been listed as one of the 100 most important chemicals in the world. However, huge amount of residual H₂O₂ is hard to timely decomposed into O₂ and H₂O under acidic condition, easily resulting in explosion hazard. Here, we reported a core–shell structure catalyst, that is graphene with Co N structure encapsulated Co nanoparticles. Co N graphene shell serves as the active site for the H₂O₂ decomposition, and Co core further enhance this decomposition. Benefiting from it, the H₂O₂ decomposition were close to 100% after 6 cycles without pH adjustment, which increased 6 orders of magnitude compared with no catalyst. At the same time, the O₂ generation reached 99.67% in 2 h with little metal leaching, and ·OH has been greatly inhibited to only 0.08%. This work can cleanly remove H₂O₂ with little deep oxidation and protect the process of H₂O₂ utilization to achieve a safer world.     

塔里木盆地塔西南坳陷柯东构造带甫沙4井原油来源及充注过程

甫沙4井位于塔里木盆地塔西南坳陷昆仑山前冲断带的柯东构造带上，北部和东部分别发育有柯克亚和柯东1井油气田。为研究甫沙4井原油来源与充注过程，对原油样品和连续抽提后的含油砂样各组分（游离态、束缚态、包裹体）进行GC、GC?MS和 GC?IRMS分析，与柯克亚凝析油气田油样进行油—油对比。结果表明：甫沙4井晚期充注原油组分具有C_29?32重排藿烷、重排甾烷和Ts相对含量高，C_27?29甾烷ααα 20R分布呈反“L”型，以及正构烷烃单体碳同位素值较低等特征，与柯克亚凝析油气田来源于二叠系普司格组（P_2?3p）烃源岩的主体原油（I类）地球化学特征一致。而早期充注的原油组分具有重排藿烷、重排甾烷和Ts相对含量较低，C_27?29甾烷ααα 20R分布呈“V”型，以及正构烷烃单体碳同位素值较高等特征，与柯克亚凝析油气田来源于中—下侏罗统湖相泥岩的II类原油地球化学特征一致。甫沙4井经历3个阶段成藏过程：①在上新世，二叠系烃源岩于生油晚期阶段生成的I类原油运移至柯克亚构造带或柯东构造带深部形成油藏；②在更新世早期，侏罗系烃源岩于生油早—中期生成的II类原油运移至甫沙4井白垩系储层；③在第四纪，强烈的构造作用使深部I类原油沿断裂调整进入甫沙4井白垩系储层。最终造成甫沙4井白垩系储层II类原油先充注，I类原油后充注的特殊现象。     

Gelling behavior of MgAl2O4 slurries with a common dispersant

MgAl₂O₄ transparent ceramics were shaped by a commonly used polyacrylic acid (PAA), which acted as both dispersant and gelling agent. The spinel slurries were prepared by ball-milling MgAl₂O₄ powder, PAA, and water in an attrition mill. The gelling of slurries happened at room temperature in air atmosphere without any other organic additive. The gelling mechanism was the formation of chelates between Mg²⁺ and carboxyl groups (-COO⁻) of PAA. The frequency-based testing method was applied to investigate the gelling process of the as-prepared slurry. In addition, a novel in situ characterization method based on a modified indentation testing was invented to better understand the strengthening of the wet green body with time and to guide when demolding could be carried out. After sintering, transparent MgAl₂O₄ ceramics with high in-line transmittance were resulted.     

基于重要度排序的配电自动化终端优化布局方法

针对配电自动化终端优化布局问题，提出了一种基于重要度排序的终端优化布局方法。首先以等年值综合费用为目标函数，供电可靠性和投入产出比为双重约束建立了配电自动化终端优化布局模型。然后通过分析配电自动化终端对供电可靠性提升的影响，给出各个节点的“二遥”及“三遥”终端安装重要度定义及计算公式。最后采用枚举法确定最优终端安装数量，基于节点终端安装重要度排序确定终端的最优安装位置。该方法考虑了已布局节点对剩余节点终端安装重要度的影响，能够在降低计算量的同时兼顾布局合理性。运用所提方法RBTS-BUS2系统及扩充模型进行终端优化布局并与智能优化算法的布局结果进行对比，验证了本文方法的有效性及优越性。